Rotational Molding design experts can expose most all design issues inside of the initial design meeting, going over the features and functionality of the new rotomolding project. Generally with some education or direction, most design issues can be avoided, which may cause manufacturing or quality issues in production. Some of the most commonly experienced rotational molding design issues are listed below in effort to help you avoid these issues when working on your rotational molding project design.
The design process for rotomolding is crucial to ensure that the aesthetics of the final product meets or exceeds the clients expectations. The repeatability of the aesthetics in a rotomold product design should be addressed in the early stages of the design process. It is important that all aesthetic considerations be carefully thought through as all of the rotomolding design stages are carefully inspected, as it is important to ensure that all of the details and features are quality captured to meet or exceed the customers expectations.
草案的角度是一个评论家al part of the rotomolding design process. Draft requirements for draft angles are crucial as they could potentially be the difference between a part having to be destroyed to be removed from a mold and a part that releases itself from the mold as it cools. Geometry, heavy texture finishes and even engraved features such as logos, warning text plates or gallonage markers could require additional draft angles in comparison to simple geometric shapes such as a block, cube or a cylinder, such as a vertical water tank. A general rule of thumb, engraved features such as logos or text can function successfully with as little as 3 degrees of draft while undercuts and protruding features may require as much as 5 degrees of draft.
One of the design issues that has the ability to plague many plastics manufacturing processes is sharp corners. Sharp corners should be avoided if at all possible during the rotomoulding design phase. Sharp corners tend to have the ability to minimize material flow through the mold during the molding process, which could cause voids in other areas, as the sharp corners tend to cause the material to not fill in properly where the material could not lay down or flow properly though the mold. Sharp corners also tend to create stress risers in the product, developing an area capable of failure or fatigue.
Because of the manner in which sharp corners are created in the design process, sharp corners become a production issue for therotomolding process. Sharp corners should be be avoided if at all possible. Sharp corners typically will create a heat sink, an area that collects more heat than in other areas of the mold, thus building up thickers areas of wall thickness with thin inside corners.
材料旋转成型过程是extbetway必威手机平台remely different than for other plastics manufacturing processes such as injection molding, blow molding or compression forming. Material for the rotational molding process requires the polymer pellets to be pulverized to powder, typically a 35 mesh, where as injection molding requires the material to be in pellet form. The additional step in pulverizing the material to a powder is necessary for rotational molding. During the cook cycle of the process, the air that is caught between the polymer particles is being heated in effort to drive out all of the air. Because of the rotation in the process and the powder materials, getting the material to flow succinctly throughout the mold is a crucial step. An experienced rotomolding engineer should be able to see any potential “bridging” or “webbing” issues between wall surfaces, not allowing the material to flow through the mold properly. The restriction of the material flow will cause voids in other areas of the product.
A general rule of thumb to avoid material flow issues is for a minimum of 5 times the wall thickness between any walls, ribs or surfaces in the product in effort to avoid material flow problems.
在滚塑设计过程必威手机网页版中,平坦的墙壁possibly the most common of design issues that plague a rotationally molded product design. Long or large flat surfaces are a nuance to the process, as typically the rotomolding process is trying to form a hollow vessel, as typically the parts have little to no internal structure. Rotomoulding experts will know how to work with your design and desired features to avoid the large flat surfaces, by breaking up the large flat areas by adding geometry or structure to the product. This is often done by adding ribs, kiss-offs or even engraved text or logos to the surfaces.
The rotational molding industry has a standard shrinkage tolerance of 1%.betway必威下载格兰杰塑料公司is one of the few rotomolding leaders that can hold a tighter tolerance on many applications through a multitude of practices. These shrinkage, warpage, cooling and other factors are all considerations that have influence on the final molded product. Industry standards for a flatness are ± .20″ per inch.
Designing For Rotational Molding
The rotational molding process has far more flexibility to accommodate the design of products and components or tooling that is required to produce products via rotational moulding. While molds or tooling can be modified once it is created, it is always beneficial to have the tooling as close as possible to the end desired result initially in effort to save time and money. Because of rotomouldings ability to change the wall thickness of the final product by altering the shot weight, or the amount of material placed in the mold without having to make modifications to the molds.